> For the complete documentation index, see [llms.txt](https://docs-origin.anvil.bot/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://docs-origin.anvil.bot/user-guides/setting-up-the-anvil-dream-labs-kit.md).

# Setting up the Anvil Dream Labs Kit

### What's in the box

<figure><img src="https://4223670213-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FT8swLPls6cg6zxcYD7sj%2Fuploads%2F0XgHLaj0In1jkVFZXOsN%2FIMG_1023.jpg?alt=media&amp;token=24986ca0-d29c-41e6-bfbf-7f9887190e7a" alt=""><figcaption></figcaption></figure>

1 x [Devbox 2.0](https://docs-origin.anvil.bot/products/anvil-devbox.md) (Dream Labs SDK pre-installed)

2 x [OpenYAM](https://docs-origin.anvil.bot/products/openyam.md) arms (white shells) each with a [Customizable Gripper](https://docs-origin.anvil.bot/products/customizable-gripper.md)

1 x Bimanual bracket (ships in 2 pieces) with M6x20 screws and nuts

2 x C- clamps &#x20;

3 x Intel Realsense D405 Cameras

4 x Gripper camera mounts (2 extra)

2x Scene camera mount (1 extra)

You'll also need: A flat, sturdy table, a hex key set, and two wall outlets

### Unbox the Robots

<figure><img src="https://4223670213-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FT8swLPls6cg6zxcYD7sj%2Fuploads%2FR1H3hNJxaS0a7svJEuC9%2FIMG_1026.jpg?alt=media&amp;token=5357e317-a1ec-42e2-80a7-a3cc87629477" alt=""><figcaption></figcaption></figure>

OpenYam will come boxed as shown above. Lift both OpenYAMs out and set them on the table. Grippers come pre-installed.&#x20;

### Assemble the Bracket

Slide the camera bar over the L connectors on the main frame and tighten the set screws.&#x20;

<div><figure><img src="https://4223670213-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FT8swLPls6cg6zxcYD7sj%2Fuploads%2F8xutnklDU2APM88BADVi%2FIMG_1029.jpg?alt=media&amp;token=e8a28525-4cc6-44c1-a362-071e2f1ab8d3" alt=""><figcaption></figcaption></figure> <figure><img src="https://4223670213-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FT8swLPls6cg6zxcYD7sj%2Fuploads%2FqHgDn5Rwqp6bvZXtVJpb%2FIMG_1030.jpg?alt=media&amp;token=1efea142-023d-4675-adb9-9a8fed9893dd" alt=""><figcaption></figcaption></figure></div>

Clamp the frame to your table with both C-clamps, otherwise the **arms may tip when they move.**&#x20;

<figure><img src="https://4223670213-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FT8swLPls6cg6zxcYD7sj%2Fuploads%2FDxbAWCa3v2NV0Djizn5C%2FIMG_1032.jpg?alt=media&amp;token=f785ba3a-9a8e-4c35-9718-eae1f46aa51a" alt="" width="375"><figcaption></figcaption></figure>

### Attach the robots

Bolt each OpenYAM base plate to the frame with 4 M6x20 screws— two in each of the frame's two channels (T-slot nuts are pre-installed). Push both arms to the outer ends of the frame. Seen from the front (scene camera facing you), the arrow on each OpenYAM base plate should point to the right.&#x20;

<div><figure><img src="https://4223670213-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FT8swLPls6cg6zxcYD7sj%2Fuploads%2FSdqoLxwFDjmFdRTKOybR%2Fs03a_place_arm.png?alt=media&amp;token=a3dc5a00-5d81-4ce5-98f9-ece84778477f" alt=""><figcaption></figcaption></figure> <figure><img src="https://4223670213-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FT8swLPls6cg6zxcYD7sj%2Fuploads%2FIl8KqjgY1bg6nVsEdEK4%2Fs03b_topdown.png?alt=media&amp;token=347cb140-d9e7-4017-9029-271a882a5755" alt=""><figcaption></figcaption></figure></div>

### Attach the scene camera

Attach the scene camera mount with a screwdriver and two M6x12 screws, then attach camera to threaded mount. Adjust camera positioning by loosening the screw on the bottom of the camera mount.

<div><figure><img src="https://4223670213-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FT8swLPls6cg6zxcYD7sj%2Fuploads%2F4I9CA9gwG2j48BaqiSLM%2FIMG_1038.jpg?alt=media&amp;token=cb0ff4a4-e919-48be-b2e5-79f4b252a8ff" alt=""><figcaption></figcaption></figure> <figure><img src="https://4223670213-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FT8swLPls6cg6zxcYD7sj%2Fuploads%2FxmWlVyebD43eNiwcSP7d%2FIMG_1043.jpg?alt=media&amp;token=d0f96429-b7a6-4585-9970-316479cc9289" alt=""><figcaption></figcaption></figure></div>

### Attach the wrist camera

Use 3 x M3 screws to attach the three holes at the top of the gripper. Then attach the D405 camera with 2x M3 screws as shown in the photo. Attach the Micro B to USB A cable to the D405.&#x20;

<figure><img src="https://4223670213-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FT8swLPls6cg6zxcYD7sj%2Fuploads%2FHr9SaS2c00aLQ6pKSRnv%2FIMG_1039.jpg?alt=media&amp;token=5bab9824-3d19-40de-8970-23dd53f3df54" alt="" width="375"><figcaption></figcaption></figure>

### Connect to Devbox

Every cable is labeled and matches a port label on the back of the devbox. Connect each camera's usb cable to its labeled usb port, then each arm's CAN/power cable to its labeled XT30 port. **Plug in the robot CAN before powering on**; hot swapping the CAN cables can lead to a drop in the CAN bus until you reboot the devbox. Run both power cables from the devbox to the wall. Turn on both power switches on the back of the robot.&#x20;

<figure><img src="https://4223670213-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FT8swLPls6cg6zxcYD7sj%2Fuploads%2FBqSTN3igC2d6nIQWZ9VZ%2Fc00_devbox_ports.png?alt=media&amp;token=0a4dcbb8-b616-400d-bbeb-8263b3010b00" alt=""><figcaption></figcaption></figure>

### Connect to Dream Labs API and Prompt

Once the devbox boots, add your API key and start prompting! More details about the API available on [Dream Labs' website](https://dreamlabs.ai/).&#x20;
